61-SO 4” OVERFILL PREVENTION VALVE
OP.0061.SO
› Works independent of pressure and only operates
directly from liquid level
› Is a two-stage shut-off valve. When the liquid level
rises to about 95% of tank capacity, the valve mechanism
is released to reduce the flow rate to 18.9 liters/minute.
If the delivery is not stopped and the liquid rises to 98%
of tank capacity then the valve closes completely and no
additional liquid can flow into the tank unless product
liquid is sold from the tank.
› Atex Approved
1-2100 SERIES THREAD-ON SPILL CONTAINER
› Designed to accommodate the fuels of the future, including methanol, ethanol and fuels with MTBE additives.
› Integral Pull-to-Open Drain Valve allows high-speed drainage of excess product into the tank
› Available in true 18.9 liter capacity as well as 56.8 liter capacity.
› Rain shedding cast aluminium cover and the seal prevents surface waters from entering the unit.
› Matches the Highway 20 rating.
10 SERIES EMERGENCY SHUT-OFF VALVES
OP.10.BF
› 1.5” Female threaded - please contact us for 2”
models.
› Shuts off the fuel both on the product side and the
dispenser end thanks to its double poppet design
› Due to its fusible link tripping the valve closed at
nearly 74 degree celcius, it shut-offs the fuel supply and
provides protection against fire.
› Allows the fuel line to be tested without any
disassembling via its 3/8” integrated test port
› Patented Thermal Relief Valve – relieves excessive
pressure over 1.72 bars caused by thermal expansion
of fuel in the dispenser piping system in theevent of fire
(double-poppet models only)
› Atex Approved
60V SERIES VAPOR LINE SHEAR VALVES
OP.BHG.0060.VP.1001
› 1” Female connection to both dispenser and
underground piping
› Corrosion resistant Duratuff Body
› Double-poppeted design incorporated to help prevent
vapor loss in the event dispenser is toppled.
› CARB approved.
70 SERIES VERTICAL CHECK VALVES
OP.70.007L.1
› 1.5” Female threaded
› Thermal relief valve reduces pressure build up in
suction pumps and opens between 1.7-2.4 bar
› Provides a rigid mounting with its three connection
points
› Single poppet design
634 SERIES TIGHT-FILL TOP-SEAL CAPS
OP.634.TT.7085
› Mates with 4” tight-fill adaptors
› Corrosion resistant Duratuff body
› Padlock or wire seal attachable cap design
› Water and vapor-tight Buna-N seal
634 SERIES TIGHT-FILL TOP-SEAL CAPS
OP.634.TE.7085
› Mates with 3” tight-fill adaptors
› Corrosion and rust resistant Duratuff body
› Padlock or wire seal attachable cap design
› Water and vapor-tight Buna-N seal
1711T 3” VAPOR RECOVERY CAP
OP.1711.T
› Mates with 1611 series vapor recovery adaptor
› Corrosion and rust resistant Duratuff body
› Padlock or wire seal attachable cap design
› Water and vapor-tight Buna-N seal
1611 SERIES VAPOR RECOVERY ADAPTOR
OP.1611.AVL
› Vapor-tight poppet only opens up the vapor path when
the unit is connected to a vapor recovery elbow or vapor
recovery composite hose
› Designed to be used in stage 1 vapor recovery
applications
› Mates with 3” vapor recovery adaptors
320 DVB VAPOR RECOVERY FLOAT VENT VALVE
OP.320.DVB
› Used in stage 1 vapor recovery aboveground vent
manifold
› In case of an overfill running thorugh the vent line, the
stainless steel ball inside the unit rises with the liquid
until it sits on its groove preventing any product transfer
to other tanks, still allowing vapor to pass through.
23 SERIES OPEN ATMOSPHERIC VENT
OP.023.UK
› 2” and 3” connection options
› Aluminium body and 40 mesh brass screen
› Special cap design to drain rainwater entry to outwards
› Protects tank vent lines from debris and blockage from
water
